[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Date Index][Thread Index][Author Index]

Re: FCB expression pedal to edp problem



Okay have tried that same dissappointment
check this with edp and fcb still set to cc30
i have connected midi out of edp to logic pro so i can watch whats 
being output by the edp.
Move edp feedback knob and it shows channel 6 controller 30 range 0-127 
great
move behringer expression set to controll 30 channel 6 range 0-127 
whislst still plugged into the edp...
and I get a range of midi notes on a range of midi channels with a 
range of value and the edp  occasional does some strange things.

remove fcb1010 from edp plug straight into logic and reads either F 
sharp 0 midi channel 6 range 0 to 127 or sometimes controller 30 midi 
channel 6 range 0-127. I am not sure if they are the same thing? it 
depends how many times I press the 1 footswitch as to which value the 
expression pedal reads in logic. mostly it says f- sharp 0, however 
sometimes controller 30.
Arrghh!
I new this would be a nightmare!
I must have missed something.... but what!
geoff




On 30 Jan 2005, at 23:08, Per Boysen wrote:

> On Jan 30, 2005, at 23:41, geoff smith wrote:
>
>> I have been putting off learning this for a while, as i new it would 
>> be a strain!
>> I have searched the achives and can't find the answer in there having 
>> tried' fcb1010' 'fcb expression' etc.
>> the problem I am having is getting the expression pedal of the fcb to 
>> control the feedback of the edp.
>>
>> I have checked with my computer that the fcb is sending controller 1 
>> value range 0-127 on channel 6 (using a max midi monitor)
>> My edp is set to receive on midi channel 6 the feedbkcontrol is set 
>> to a value of one, I have checked that when I plug the echoplex into 
>> computer moving the feedback knob send a  controller 1 value range 
>> 0-127 on channel 6
>> So they are the same so why then when I move the expression pedal on 
>> the fcb it sets the feedback on the edp to 0 no matter where I move 
>> it.
>> I programmed the the fcb by pressing button one so it lights up, 
>> holding down 'down' for 2.5 secs, pressing up to avoid switches, 
>> lighting switch 8 for expression pedal A so it flashes, pressing 
>> enter, setting a value of 1 (as for feedback) pressing enter, setting 
>> low range to 0 press enter, and high range to 127 press enter and 
>> then leaving.
>>
>> So what have I done wrong as if I plug fcb into computer its sending 
>> 0-126 on cc 1 midi channel 6.
>> Please help as i am totally confused
>> geoff
>>
>> p.s. I have programmed all the footswitches to control edp parameters 
>> with no problems.
>
>
> Very, very, very strange! You've done it right after the book and even 
> double checked everything. The only plausible explanation seems to be 
> that the EDP feedback midi control for some reason does not work with 
> midi cc 1 ("modulation wheel").
>
> Since you have now developed a talent in programming both the EDP and 
> the FCB you may try to use another midi cc to see if it's working? 
> Over here I have been using midi cc 30 on midi channel 1 and it has 
> never let me down.
>
> Greetings from Sweden
>
> Per Boysen
> ---
> http://www.looproom.com (international)
> http://www.boysen.se (Swedish site)
> http://www.cdbaby.com/perboysen
>
>