[
Date Prev][
Date Next] [
Thread Prev][
Thread Next]
[
Date Index][
Thread Index][
Author Index]
OT: [all] stereo to mono phase problems
Ok--wait, what? Let's clarify your cabling:
Your mixer has 1/4" and XLR ins, balanced or unbalanced 1/4" outs. For
source input purposes:
>From multitrack: should be 1/4" TRS (if the multitrack has balanced outs)
to 1/4" TRS. Use regular 1/4" TS if the multitrack has only unbalanced
outs.
>From the CD players: you've probably got RCA outs from the CD player, so
either, use the RCA to 1/4" TS adaptors I think you're talking about, or go
invest $15 in a pair a good RCA to 1/4" cables.
>From the DJ mixer: again, probably RCA outs. Use the above cable
>solution.
If by chance the mixer has 1/4" outs, they will definitely not be balanced,
so use regular 1/4" TS cables.
For outputs:
To the amp: your mixer provides balanced outs, so if your amp does, use
1/4" TRS, else stick with basic 1/4" TS.
To the speakers: use the thickest gauge you can fit into your speakers'
binding posts (or whatever connector they might have--banana, 1/4",
whatever...)
To the tape player: I'd use the same 1/4" TS to RCA cables mentioned above
to run the CR out to the tape deck (or CD burner, or DAT, or whatever your
stereo mixdown destination is).
I agree with Hans: avoid the adapters.
"Paul Buelow"
<paul@webms.c To:
<Loopers-Delight@loopers-delight.com>
om> cc:
Subject: Re: [all] stereo to
mono phase
11/06/00 problems
03:07 PM
Please
respond to
Loopers-Delig
ht
Wow, Excellent Lindsay. Thank you.
I will do some thorough testing now with this info. It's a very helpful at
approach to use to resolve the muddy mono monitor sound problem (thought it
doesn't affect recording or headphones).
I am using phono to RCA adapters on the control room outs which are plugged
into the TRS balanced phono outs. Aha? could be poorly wired +/- adapters.
In considering the best cable for main outs or control outs, I wonder what
type of cables to use if cabling from the balanced TRS phono outs to a
non-balanced input such as a tape deck.
non balanced cables or TRS phono balanced to non-balanced?
----- Original Message -----
From: <lindsay@pavestone.com>
To: <Loopers-Delight@loopers-delight.com>
Sent: Monday, November 06, 2000 12:25 PM
Subject: OT: [all] stereo to mono phase problems
>
> Hmmmm.
>
> Source material:
> Multitrack channels: mono
> CD player: stereo
> DJ-600 mixer: stereo
> (mixing stereo sources?)
> Mic: mono
>
> The above are not likely to come from the source out-of-phase. Next
step:
> investigate individual mixer channels.
>
> Alesis Studio 32: phase invert not available (at least I can't find it
> listed in Alesis' on-line documentation). So rule that out.
>
> Next: cabling from mixer to amp. Main outs are 1/4" TRS (balanced or
> unbalanced). If I remember right, the phase-inverted signal of a
balanced
> output is on the ring part of the TRS cable. I doubt that your mixer's
> wiring could be that screwed up to have the tip and ring switched on one
> output. However, there is the slightest possibility, so try avoiding the
> main outs from your mixer--you've got control room outs as well as group
> and aux outs; mix down to a pair of those and see if you still have the
> "muddy" problem. If so, then there's your problem--the main outs. If
not,
> well...
>
> I doubt the problem is in the cabling itself--if it was a cabling problem
> (as in faulty cable), then you'd have the same problem all the time, not
> just when panned to center.
>
> The amp? Man, I can't think that the amp is the problem. But, as a
test,
> get some 1/4" to RCA cables and run them from your mixer's main outs and
to
> your home stereo's tape or CD in. Listen to your mix through your
stereo.
> Does the problem persist? Actually, this test would rule out everything
> downstream of your mixer: the cables, the amp, the speaker wire and the
> monitors. Try this out.
>
> If the above test fails to reproduce the problem, then it has to be
> downstream of the mixer. Check the polarity of all your wiring. Make
sure
> it's consistent for both sides. Actually, you've probably done this
> already a thousand times. So, confident that the wiring to and from the
> amp is correct--and that the problem still persists--switch the polarity
of
> the leads coming into only one speaker. We're now deliberately out of
> phase with the other speaker. Still have the problem? At this point, I
> doubt phase is the issue. Move your speakers to a new position. Maybe
you
> just have one wickedly bad sounding room (though this should be evident
in
> the stereo mixes, too). I can't think of anything else, and I've already
> been long-winded enough.
>
>
>
> "Paul Buelow"
> <paul@webms.c To:
<Loopers-Delight@loopers-delight.com>
> om> cc:
> Subject: Re: [all] stereo to
mono phase
> 11/06/00 problems
> 01:51 PM
> Please
> respond to
> Loopers-Delig
> ht
>
>
>
>
>
> > what is the nature of the source program material?
> >
> I've experienced the phase problem with a variety of sources and isolated
> it
> to a problem between the mixer and the amp + speakers. The mixer is an
> Alesis32. Monitoring through the mixers headphone output does not exhibit
> the same muddy result when panning to center.
>
> I have ruled out the source as the problem. The source is fine when
patched
> directly to the amp (hence no panning to center). Is panning to center
> inherently going ot cause a phase problem. Could it be the room or
speaker
> position causing a problem? The source is either mono tracks from a
digital
> multitrack deck, CDs, DJ-600 mixer output or mic input.
>
> It appears to be a problem with the relationship between my cabling
and/or
> monitor wiring.
>
>
>