Re: 2nd EDP+ for stereo

[Luis Angulo <labalou2000@yahoo.com>]

ok,so far so good except when i do a lot of replace
they drifted at times out of sync, has that happen to
you yet?

--- Kris Hartung <khartung@cableone.net> wrote:

> I didn't dump them, rather I just programmed one and
> other one followed 
> along because of the MIDI connection between the
> two.
> 
> Kris
> 
> ----- Original Message ----- 
> From: "Luis Angulo" <labalou2000@yahoo.com>
> To: <Loopers-Delight@loopers-delight.com>
> Sent: Monday, January 16, 2006 12:38 AM
> Subject: Re: 2nd EDP+ for stereo
> 
> 
> > Hey Kris,
> > Can u tell me how to quickly dump all the presets
> from
> > the master EDP to the slave?
> > thanx
> > Luis
> >
> > --- Kris Hartung <khartung@cableone.net> wrote:
> >
> >> I use two EDPs in true stereo. We've had this
> >> discussion before on the list,
> >> and playing in stereo is less important to some
> than
> >> others, but for me it
> >> is essential to my "current" sound, given all the
> >> stereo imaging I use with
> >> my laptop VST effects. I'm also an addict of lush
> >> stereo chorus and stereo
> >> delay where the left side is lightly longer than
> the
> >> right.
> >>
> >> In any event, I have had no troubles with my
> setup,
> >> except initially when
> >> trying to figure out how to get the two EDPs to
> sync
> >> up and prevent signal
> >> drift. When you get to that point, send me an
> email
> >> and I'll send you the
> >> list of parameters.
> >>
> >> I run from my into my Boss VF1 from my guitar,
> out
> >> of the VF1 in stereo,
> >> into my laptop in stereo, out of the laptop in
> >> stereo, into my Mackie mixer
> >> board (two channels panned left and right), and
> then
> >> I run out of the
> >> mixer's BUSS 1 into the input of one EDP, and out
> of
> >> BUSS 2 into the input
> >> of the other EDP....then out of the two EDPs into
> >> two channels of the board,
> >> panned left and right. This way, when multiple
> >> people or instruments are
> >> plugged into my board, I can simply press the
> buss
> >> 1/2 button on their
> >> channel and loop them in my mix. I run an Lexicon
> >> LXP1 in my mixer's AUX 1
> >> channel, and back into a stereo channel of the
> board
> >> for a nice reverb on
> >> everything.
> >>
> >> I think the results are especially noticeable and
> >> fun when you are recording
> >> off the board....then the stereo imaging really
> pops
> >> out, if you are using
> >> effects that to tricks in stereo.
> >>
> >> Kris
> >>
> >> ----- Original Message ----- 
> >> From: "Dennis Montgomery"
> <morpheus@speakeasy.net>
> >> To: <Loopers-Delight@loopers-delight.com>
> >> Sent: Thursday, January 12, 2006 6:58 PM
> >> Subject: 2nd EDP+ for stereo
> >>
> >>
> >> > Hi all,  I currently take the output from my
> lone
> >> EDP+ and send it through
> >> > an Alesis Microverb III to get some
> pseudo-stereo
> >> separation.  I'm
> >> > considering adding a 2nd EDP+ so I can process
> my
> >> loops in true stereo.  I
> >> > was wondering if any players who have taken
> this
> >> step can comment on their
> >> > experience of using a 2 EDP+ stereo system? 
> Did
> >> it really make a
> >> > difference in your playing fun?  Any technical
> >> problems?   etc...
> >> >
> >> > Dennis
> >> >
> >> >
> >>
> >>
> >>
> >
> >
> > www.luis-angulo.com
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam?  Yahoo! Mail has the best spam
> protection around
> > http://mail.yahoo.com
> >
> > 
> 
> 
> 


www.luis-angulo.com

__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com