|
Hi there....talk about problems!!! With the CC fudge-solution sugested here I can get the following by keeping the cc's on channel1 with a source offset of 36 BOTTOM ROW 1 record using just one cc...and a Value of 38-01 (I then tried using a value of 38-01 as CC1 followed by a value of 38-00 ...this resulted in having to tap the pedal en extra time before it would begin or stop recording , i dont know why.) 2 overdub again seems to work using just one cc 39-01 3 multiply again just one cc seding out 40-01 4 half speed 48-01 5 reverse 49-01 (should these have other numbers following them in a seccond cc? if so can someone give an example I can work with?) TOP ROW 6 Mute 42-01 seems to work now 7 Sus Overdub ...cant find any combination of cc's to work 8 Sus Replace ... again can't get working 9 Undo CC1 43-01.... CC2 43-00 .......seems to kind of work but the EDP light goes perminantly red and this sometimes seems to glitch and stop all other buttons working 0 Next Loop 44-01 on another page I have also been tying to get reset but cant get it to work consistently (sometimes it seems to work but not always)using cc1 62-01 followed by cc2 62-01 the nmbers are the order in which i put them into the fcb1010 hope it makes sense, am i putting them in the wrong order or choosing incorrect numbers? i just dont know where to start. OK If i have to move on and get more kit I think my first port of call will be Uno, is anyone using an Uno modded FCB1010 with a EDP using CC's on here? does it work? I would love to hear from you. Many thanks for continued help Phill Wilson > Date: Mon, 21 Apr 2008 21:05:45 +0100 > From: akbutler@tiscali.co.uk > To: Loopers-Delight@loopers-delight.com > Subject: Re: Programming the FCB1010 for the EDP (Karma) > > hi Phillip > > You can use CC to operate an EDP, > but using the fcb1010 gives limited results, > as the edp needs the CC equivalent of Note-Offs > if you're going to get the same results. > > i.e. if when you released he switch you > could send the corresponding CC with a value of 0 then all would be > well, thus giving you all the needed LongPress and ShortPress functions. > ...but the fcb doesn't do that > > > Just sending the first CC on it's own always gives you LongPress, > ...so every time you try Record, you get a Reset :-( > > > As fcb can send 2 CCs, you could program in a ShortPress, > by sending the CC of value 0 immediately after the CC for the function. > ..but problem is you have to program another switch if you want the > LongPress at all. > > Lack of EDP3 response....check the fcb global midi channel for the CCs. > > > Conclusion...it doesn't work that well :-( > > Suggestion...use a Midi Router instead. Andre Lafosse controlled 5 edps with one of those. > > Or..Get the Uno firmware upgrade for you fcb which solves the CC problem. > > > andy butler > > phillip wilson wrote: > > Hi Erland..and all... > > > > Heres a deal for you....Erland, I will email u offlist and work this > > through with u, I have two EDPs up and running with the FCB > > perfectly..Im confident I can get u up and running. > > > > HERES THE CATCH EVERYONE ELSE---- > > Will someone further up the ladder in EDP usership help ME!!! > > > > I need to control 3 EDPs of one Behringer FCB1010.... > > so far I can get two to play using notes and offsets of 0 and 48 on > > Channel 1...........but if I try to add the same commands for EDP3 I run > > out of midi notes at the top end (would need 137) If i bunch the offsets > > closer together there seems to be cross talk between the desired > > function on EDP3 and some undesired function on EDP2 due to overlap. > > > > I am therefor hoping I can use FCB1010 with the edp set to CTR instead > > to grab them last buttons, however at the moment I cant get any reaction > > at all out of EDP3 > > > > It is still set to channel 1 same as the notes and I have brought the > > offset back to 0 seeing as we are using CTR's so there shouldnt be any > > miss-infomations (right???) basically if you have made an EDP work using > > a behringer FCB1010 and CTR's I would love to hear from you. > > > > Pay It Forward > > > > Phill > > > > > Date: Mon, 21 Apr 2008 19:20:09 +0200 > > > From: perboysen@gmail.com > > > To: Loopers-Delight@loopers-delight.com > > > Subject: Re: Programming the FCB1010 for the EDP > > > > > > On Mon, Apr 21, 2008 at 6:28 PM, Erland <erlandka2@gmail.com> wrote: > > > > Is there a guide out there to programming the FCB1010 for use with > > the EDP > > > > other than the Behringer and Echoplex manuals? > > > > I've already given up a few times even though I find myself quite > > > > technically minded. > > > > > > > > I'm mostly interested in the granular functions and feedback pedal as I > > > > already have the Gibson and Digitech footcontrollers. > > > > > > > > > > > > Thanks much, > > > > > > > > Erland > > > > > > > > > Try searching the archives of this list! The topic has been up many > > > times. I bet you will find at least three good guides ;-) > > > > > > -- > > > Greetings from Sweden > > > > > > Per Boysen > > > www.boysen.se (Swedish) > > > www.looproom.com (international) > > > www.stockholm-athens.com > > > > > > > > > ------------------------------------------------------------------------ > > Try Messenger on your mobile. Text MSN to 63463 Now. > > <http://mobile.uk.msn.com/pc/messenger.aspx > > Have you played Fishticuffs? Get fish-slapping on Messenger |